Lenovo ThinkServer RD340 Manual de usuario Pagina 69

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 214
  • Tabla de contenidos
  • SOLUCIÓN DE PROBLEMAS
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 68
4.PressF10tosavesettingsandexittheSetupUtilityprogram.Theserverwillrestarttoenablethe
TPMfunction.
SettingthemodeoftheEthernetconnectors
TherearethreeRJ-45Ethernetconnectorsontherearoftheserver.TheEthernetconnector0isforsystem
managementbydefault.However,youalsocansettheEthernetconnector1or2forsystemmanagement
use.Youalsocaninstallanoperatingsystemthroughthesystem-managementconnector.Tolocatethe
threeEthernetconnectors,see“Rearviewoftheserver”onpage23
.
IfyousetoneoftheEthernetconnectorsforsystemmanagement,theothertwoEthernetconnectorscanbe
teamed.IftwoEthernetconnectorsareteamed,theteamedconnectionspeedwillbethesamewiththe
lowerconnectionspeedofthetwoEthernetconnectors.
EthernetconnectorforsystemmanagementEthernetconnectorsforteaming
Ethernetconnector0Ethernetconnector1andEthernetconnector2
Ethernetconnector1Ethernetconnector0andEthernetconnector2
Ethernetconnector2Ethernetconnector0andEthernetconnector1
TosetthemodeoftheEthernetconnectorsintheSetupUtilityprogram,dothefollowing:
1.StarttheSetupUtilityprogram.See“StartingtheSetupUtilityprogram”onpage51.
2.OntheServerManagementmenu,selectBMCNetworkConfigurationBMCLANShareSetting.
3.Dooneofthefollowing:
TousetheEthernetconnector0asanEthernetconnectorandalsoasystem-managementconnector,
selectManagementNICShared.
TousetheEthernetconnector0asadedicatedsystem-managementconnector,selectManagement
NICDedicated.
TousetheEthernetconnector1asanEthernetconnectorandalsoasystem-managementconnector,
selectOnboardLANport1Shared.
TousetheEthernetconnector2asanEthernetconnectorandalsoasystem-managementconnector,
selectOnboardLANport2Shared.
Note:IfyousetoneEthernetconnectorasthesystemmanagementconnector,theothertwoEthernet
connectorswillbeordinaryEthernetconnectorsbydefault.
4.PressF10tosavesettingsandexittheSetupUtilityprogram.
ExitingtheSetupUtilityprogram
Afteryoufinishviewingorchangingsettings,pressEsctoreturntotheSetupUtilityprogrammaininterface.
Ifyouareonanestedsubmenu,pressEscrepeatedlyuntilyoureachthemaininterface.Then,youcando
oneofthefollowingtoexittheSetupUtilityprogram:
IfyouwanttosavethenewsettingsandexittheSetupUtilityprogram,pressF10orselectSave&Exit
SaveChangesandExit.Otherwise,yourchangeswillnotbesaved.
Ifyoudonotwanttosavethenewsettings,selectSave&ExitDiscardChangesandExit.
Ifyouwanttoreturntothedefaultsettings,pressF9orselectSave&ExitRestoreDefaults.
FormoreinformationabouttheSave&ExitmenuintheSetupUtilityprogram,see“Save&Exitmenu”
onpage54
.
Chapter5.Configuringtheserver57
Vista de pagina 68
1 2 ... 64 65 66 67 68 69 70 71 72 73 74 ... 213 214

Comentarios a estos manuales

Sin comentarios